Tag: accidents

Tire Safety

Posted on by admin_ici
Originally published 08/30/2019

A commonly-overlooked object on any piece of equipment is the tires. In construction, we work with, and around, rubber-wheeled equipment all the time. Properly maintained tires improve vehicle handling, fuel economy, the load-carrying capability of your vehicle or equipment and increase the life of your tires.

Studies of tire safety show that the most important things you can do to avoid tire failure are maintain proper tire pressure, observe tire and vehicle load limits, avoid road hazards, and inspect tires for cuts, slashes or other irregularities. Doing this can help you avoid tire failure, such as tread separation, blowouts and flat tires. Here are some safety tips for proper tire inspection:

  • Inspect tires daily for uneven wear patterns, cracks, cuts, slashes, foreign objects or other signs of wear or trauma. Remove bits of glass and other foreign objects wedged in the tread.
  • Use a tire pressure gauge to check the tire pressure at least once a month. Do this when the tire is cold (meaning the tire has been still for at least three hours). You can find the manufacturer-recommended tire pressure information on the vehicle door edge, door post, glove box door or in the vehicle owner’s manual. Improper tire pressure can lead to uneven wear, making the tire less effective when stopping or turning, which may cause collisions, sliding and/or stability problems.
  • Check the tire tread depth at the same time you check the tire pressure. In general, tires are not safe and should be replaced when the tread is worn down to one-eighth of an inch.
  • Make sure the tires are properly balanced. This adjustment maximizes the life of your tires and prevents your vehicle from veering to the right or left when driving on a straight, level road.
  • Do not overload your vehicle. Check the tire information placard or owner’s manual for the maximum recommended load for your vehicle.
  • If you are towing a trailer, remember that some of the weight of the loaded trailer is transferred to the towing vehicle.
  • Slow down if you have to go over a pothole or other object in the road.
  • Do not run over curbs, and try not to strike the curb when parking.

Remember to do your part: be tire smart.

Download the recording form here.

Preventing Soft Tissue Injury

Posted on by admin_ici
Originally published 08/16/2017

Soft tissue injury is one of the most common injuries in construction. Soft tissue refers to tissues that connect, support or surround other structures and organs of the body. Here are some of the most common soft tissue injuries reported in construction:

  • Muscle sprains and strains;
  • Injuries to muscles, ligaments, intervertebral dics and other structures in the back;
  • Injuries to nerves, ligaments and tendons in the wrists, arms, shoulders, neck or legs;
  • Abdominal hernias; and
  • Chronic pain.

These injuries can occur suddenly or over a prolonged period of time. Risk factors for soft tissue injuries include awkward postures, repetitive motion, excessive force, static posture, vibration and poorly designed tools. The good news is that soft tissue injuries, and the conditions caused by them, are preventable.

The following precautions can help prevent soft tissue injuries:

  • Stretch before you use your muscles.
  • Avoid bending or twisting the back or neck.
  • Avoid overexertion.
  • Use ladders to reach overhead objects and mechanical equipment to carry and move heavy materials.
  • Use proper lifting techniques. Lift with your legs, not your back.
  • Make the most of your break times and stretch muscles that have become tense from continuous sitting and/or exposure to vibration.
  • Use tools properly. When possible, keep tools between your waist and shoulder height, which is considered the “lifting zone.” This gives you the most leverage, and allows the strongest muscles to do the work.
  • Keep your work area clean and free of hazards. Pick up loose objects from the floor, and clean up spills immediately to eliminate tripping and slipping hazards.

Take action today. Decide what you can do right now to help prevent a soft tissue injury, and then do it. You’ll end up with a safer workplace and fewer workplace injuries.
Download a recording form here.

Trench and Excavation Safety

Posted on by admin_ici
Originally published 07/12/2017

Trench collapses can occur without warning, regardless of the depth. The vast majority of trenching fatalities occur in trenches 5 to 15 feet deep. But trench cave-ins don’t have to happen. They are preventable with proper planning and execution of safety precautions.

Here are some practices that will help reduce the risk of on-the-job injuries or fatalities on excavation sites.

  1. Know where the underground utilities are located before digging.
  2. Keep excavated soil (spoils) and other materials at least two feet from trench edges.
  3. Keep heavy equipment away from trench edges.
  4. Identify any equipment or activities that could affect trench stability.
  5. Test for atmospheric hazards such as low oxygen, hazardous fumes, and toxic gases when workers are in trenches more than four feet deep.
  6. Inspect trenches at the start of each shift. This should be done by the competent person. The competent person should be authorized to order immediate corrective action, including restricting entry into the excavation, until any hazards or potential hazards have been eliminated.
  7. Ensure that employees working in trenches four feet deep or more have an adequate and safe means of exit, such as ladders, steps or ramps. These must be within 25 feet of all workers at all times and will need to be relocated as the job progresses.
  8. Inspect trenches following a rainstorm or other water intrusion.
  9. Inspect trenches after any occurrence that could have changed conditions in the trench.
  10. Do not work under suspended or raised loads or materials.
  11. Ensure that workers wear high-visibility or other suitable clothing when exposed to vehicular traffic.
  12. Develop a trench emergency action plan and train workers and supervisors on the proper actions to take in case of an emergency.

Remember: Unlike most accidents, the cave-in of an excavation can usually be predicted if closely watched. So stay alert. Don’t take anything for granted.

Download a recording form here.

Heavy Equipment Safety

Posted on by admin_ici
Originally published 07/05/2017

Only trained, highly skilled construction workers should operate heavy equipment such as excavators, loaders, graders, rollers and bulldozers. Ground-based workers should be trained in how to work safely around the equipment or stay clear. Unsafe practices by either the operator or those around the equipment can create very dangerous situations. Some of the reasons for injury to heavy equipment operators and ground-based workers on a construction site include:

  • Repairing and servicing equipment in dangerous positions,
  • Striking individuals or other vehicles with the equipment – particularly the blade,
  • Unexpected tipping of equipment,
  • Uncontrolled traffic within or through the work area,
  • Unexpected shocks or jars to the machine,
  • Sudden movement of a power unit while it is being attached to earth moving equipment,
  • Limbs of trees or overhead obstructions,
  • Leaving equipment running or in dangerous positions while unattended, and
  • Lifting mechanism failure on the equipment.

Here are a few common safety rules for operators and ground-based workers to consider:

  • Inspect and service your equipment regularly. This should be done in accordance with the manufacturer’s recommendations and by qualified personnel. A pre-shift walk around inspection by the operator is highly recommended.
  • Do not wear loose clothing that can get caught in moving parts of the equipment.
  • Keep deck plates or steps on equipment free from grease, oil, ice and mud. Corded soled shoes are recommended.
  • Check the area for ground-based workers before operating the equipment.
  • Ground-based workers should wear high visibility clothing so they can be seen by the operator. They should also wear their personal protective equipment.
  • Establish a danger zone for ground workers. Be aware of the swing radius on certain equipment and, if possible, cordon off the area with barriers or caution tape.
  • Use a spotter and establish a standardized set of hand signals to be used by the operator and spotter. Two-way radios can sometimes be valuable communication tools.
  • The spotter should maintain eye contact with the operator. This will ensure that they are not in the operator’s blind spot.
  • Make sure the back-up alarm on the equipment is in working order and use it when backing.
  • Employees other than the operator should not ride on equipment.
  • Before starting the motor, the operator should make sure that all operating controls are in the neutral position.
  • Heavy equipment should have a rollover protective structure that meets OSHA requirements.
  • Operator should wear a seat belt at all times.
  • If working on slopes, try to avoid moving across the face of the slope. Operating up and down the slope is best.
  • Keep a safe distance from open excavations.
  • Wear hearing protection when required.
  • Never jump onto or off the equipment. Operators should always use the three-point contact rule when climbing on or off equipment. This means having either both feet and one hand, or having one foot and both hands in contact with the ladder access at all times.
  • If possible, drive equipment entirely off the road at night. If any portion of the machine projects into the road, it should be adequately marked with red lights or flares at night. Use red flags in the daytime.

Injury accidents involving heavy equipment have a high probability of fatality. It is critical that you know and follow your company’s safety rules and procedures when operating or working around heavy equipment.

Download a recording form here.

Work Zone Flagger Safety

Posted on by admin_ici
Originally published 06/07/2017

Work zone flaggers are the first line of defense for road construction workers and are there to help protect the public. It is a critical and dangerous job. Because they are the ones that deal with the speeding, distracted or sometimes angry driver, they must also know how to protect themselves while on the job.

What flaggers should do to protect themselves:

  • Most importantly, all flaggers should have the appropriate flagger training and have periodic refresher training.
  • Wear high-visibility clothing such as orange, yellow or green vests. Use retro-reflective vests at night.
  • Wear other protective equipment such as hard hats, long-sleeved shirts and pants, safety footwear and eyewear.
  • Dress appropriately for the weather.
  • Stay alert and out of harm’s way by following these guidelines:
    • Stand alone on the shoulder in clear view.
    • Never stand in the open traffic lane.
    • Plan an escape route for emergencies.
    • Stay alert and focused on your work.
    • Make sure your hand signals don’t conflict with the traffic signals.
    • Treat motorists with respect and courtesy. Don’t pick fights or respond in anger. If a driver is a problem, record the make, model and license number of the car, and report the incident to law enforcement.
    • If a driver violates your warnings and trespasses your flagging station, warn the other workers in the work zone. Establish a warning signal ahead of time for the work crew in case of an emergency.

Dangerous behaviors flaggers should avoid:

  • Standing where you can be crushed;
  • Standing in the shade, over the crest of a hill or around a sharp curve;
  • Leaving your position until properly relieved;
  • Standing near equipment;
  • Standing in a group;
  • Participating in unnecessary conversation;
  • Reading or daydreaming while on duty;
  • Using your cell phone;
  • Listening to music or using ear phones; or
  • Turning your back on traffic.

Remember, working in traffic areas always presents some risks. The job of a flagger is an essential component of worksite safety.

Download the recording form here.

Tips for the Safety Supervisor

Posted on by admin_ici
Originally published 05/31/2017

In past Toolbox Talks, we have discussed the safety responsibilities of construction workers. This week, we’ll discuss ten tips for supervisors to use when supervising safety.

  1. Demonstrate a genuine concern for worker safety. Be sure your workers understand and accept personal responsibility for safety. Provide them with the proper tools to get the job done. Reinforce safety where required and lead by example.
  1. Know the rules of safety that apply to the work you supervise. Be aware of the precautions required on the job. Attend safety training to gain knowledge of safety hazards.
  1. Anticipate risks that may arise from changes in equipment or methods. Use available safety information and advice to help guard against new hazards. It may be appropriate to conduct a periodic hazard assessment of the tasks your workers perform to determine the safest method and what personal protective equipment is needed for each job.
  1. Encourage workers to help identify hazards on the job and recommend a solution. Also encourage workers to stop work on a job if they have unanswered safety questions. Let them know that providing input on safety is not only allowed, but strongly recommended.
  1. Instruct your employees to work safely, with persistence and patience. When you observe employees who are not observing the safety rules, correct the unsafe behavior immediately. Unsafe work practices that go uncorrected can have long-term effects on your safety program.
  1. Follow up on safety issues and suggestions. Keep your workers involved in your company safety program. All safety suggestions and questions deserve a response. When communication breaks down and supervisors do not respond to workers’ suggestions, workers can easily lose interest.
  1. Set a good example. Demonstrate safety in your own work habits and personal conduct so that you don’t appear hypocritical in the eyes of your workers.
  1. Analyze all accidents and near-misses. When minor injuries go unheeded, crippling accidents may strike later. Minor accidents and near-misses provide an opportunity for safety improvements that could result in avoiding a serious accident or fatality.
  1. Recognize your role in the company’s overall safety program. It is vital to know that the company’s safety director does not own the safety program and that your involvement and input is welcomed and encouraged.
  1. Embrace your supervisory role and carry it out. Remember that managing safety on the job is as important as managing the project itself. Safety on the job is an investment that always pays dividends. Every effort that we make to prevent accidents on the job leads to a more productive work atmosphere and can contribute to improved employee morale.

Download the recording form here.