Carbon Monoxide Hazards

Originally published 11/3/2016

Small gasoline-powered engines and tools used in construction can produce high concentrations of carbon monoxide (CO). CO is a poisonous gas that can cause illness, permanent neurological damage and death. Because it is tasteless, colorless, odorless and non-irritating, CO can overcome exposed persons without warning. There is often little time before they experience symptoms that inhibit their ability to seek safety.

Common signs of overexposure to CO include headache, nausea, weakness, dizziness, visual disturbances, changes in personality and loss of consciousness. Any of these symptoms can occur within minutes.

Prior use of equipment without incident has sometimes given users a false sense of safety. Recommendations for preventing CO poisoning include:

  • Educate workers about the sources and conditions that could result in CO poisoning, as well as the symptoms and control of CO exposure.
  • Conduct a workplace survey to identify all potential sources of CO exposure.
  • Use personal CO monitors where potential sources of CO exist. These monitors should be equipped with audible alarms to warn workers when CO concentrations are too high.
  • Consider the use of tools powered by electricity or compressed air if they are available and can be used safely.
  • When using gasoline-powered engines or tools outside of a building, never place them near air intakes so that engine exhaust is not drawn indoors.
  • Always place the pump and power unit of high-pressure washers outdoors. Run only the high-pressure wash line inside.

Carbon monoxide poisoning is often misdiagnosed as the flu. If you suspect that a worker has symptoms associated with carbon monoxide poisoning, take the following steps:

  • Open the doors and windows.
  • Turn off combustion appliances and have everyone leave the area immediately.
  • Since CO can cause long-term, and even permanent injury and illness, seek medical attention.

A CO detector can be a viable solution to preventing CO-related mishaps. It is a small, easy-to-install gadget that is available at most hardware stores. CO detectors usually cost less than $100, and some even combine the safety features of a smoke alarm with carbon monoxide detection.

Like other jobsite hazards, CO mishaps are preventable. We must all recognize where the hazards exist and put appropriate controls in place to avoid unintentional injuries.

Download the recording form here.

Horseplay Has No Place on the Jobsite

Originally published on 11/08/2017

Although most of us like to have fun, there is no place for horseplay on a construction site. According to the dictionary, horseplay means rough fun. Fooling around means doing foolish, useless things. Both are the opposite of safe, responsible work, and most employers ban them on the construction site.

Horseplay is generally a friendly, physical way to let off steam, but that kind of fooling around can:

  • Break your work concentration,
  • Cause you to be less likely to notice hazards until it’s too late, or
  • Cause an accident.
    • You may not notice spills or items lying on the floor.
    • You might crash into or push someone else into heavy equipment or moving machine parts.
    • You could knock boxes or materials over or onto a person.
    • You could stab someone with a sharp object.
    • Fooling around with PPE can damage it and expose you or another worker to injury or a hazardous substance.
    • Speeding or stunt driving with a forklift can cause it to tip over or hit people or objects.
    • Pushing, teasing, or otherwise distracting people working with machinery could cause pinch points or other injuries.

Horseplay can be costly to both the company and employees in doctor bills, workers comp claims, increased insurance costs and lost work. There can also be added costs to replace machinery or tools and equipment.

Employers should:

  • Make sure all employees know the rules of behavior on the job site.
  • Inform employees of the disciplinary consequences of engaging in horseplay on the site.
  • Emphasize “zero tolerance” for horseplay and practical jokes on the site.

Workers’ responsibilities include the following:

  • Do not encourage or provide an audience for horseplay or practical jokes.
  • Never initiate or participate in horseplay or practical jokes.
  • Use common sense and act professionally.

Ask yourself, “Is a coworker’s safety worth my entertainment?” Horseplay can cause severe injury and even death. Take your safety, and the safety of your coworkers seriously and wait till after you’ve left work to horse around.

Download the recording form here.

Work Gloves

Originally published on 11/15/2017

The most used tool on any construction jobsite is the human hand. The proper work gloves can help protect against cuts, punctures, abrasions, thermal burns, vibration, chemical exposures and electrical shock. No single glove will protect from all hazards, so you should select your gloves based on the hazards that will be present on the site, the job task, work conditions and the duration of use.

Gloves are perhaps the most commonly used type of PPE. Types of gloves range from common canvas work gloves to highly specialized gloves used in specific industries.

To ensure that your gloves will adequately protect your hands:

  • Wear gloves that are right for the work being performed. Check the MSDS for information on the types of gloves to be worn for specific tasks. Your company’s competent person should be able to assist in recommending the correct glove for the work task.
  • Inspect your gloves prior to each use and don’t use them if they are torn or damaged. Look for change in shape, hardening, stretching, tears or holes. Chemicals can pass through even the smallest pinhole.
  • Wear only gloves that fit your hand. Proper fit is important. If they are too large or small, they can be clumsy to work with, get in the way, and actually become a hazard.
  • Keep the insides of your gloves clean. Contaminants inside gloves can cause blisters and burns.
  • If gloves are to be reused, follow the manufacturer’s instructions for proper decontamination, cleaning and storage. Take note of the expected service life of the gloves and plan for expected disposal times.

Before starting a job, ask yourself the following:

  1. What hand hazards do we have on our site?
  2. What close calls with hand injuries have we had in the past? Is it possible on this job?
  3. Do we have the type of gloves we need onsite and ready for use?
  4. What can we do to improve hand hazards on this job?

Download the recording form here.

Accident Causes and Prevention

Originally published 10/24/2019

Accidents on construction sites generally spur questions like, “What happened?” or “How did it happen?” But accidents don’t just happen. They can almost always be traced back to an unsafe condition, an unsafe act or a combination of both. To eliminate accidents, we must eliminate unsafe conditions and acts.

Unsafe conditions are usually created by:

  • Poor housekeeping;
  • Improper storage;
  • Defective or damaged equipment;
  • Improper maintenance;
  • Removing guards from machinery and, in some rare cases,
  • Unsafe procedures.

Unsafe conditions can be eliminated if crews regularly inspect the worksite and equipment, identify any hazards that exist and correct them.

Although unsafe conditions can lead to accidents, most safety experts agree that the majority of accidents are caused by unsafe acts. These are careless things that people do that are most often the result of poor habits, taking short cuts and even disregarding safety policies and procedures.

Examples of unsafe acts include:

  • Reaching into equipment or machinery while it is running;
  • Backing equipment without looking behind the equipment or using a spotter;
  • Not inspecting tools and equipment before use;
  • Using damaged tools or equipment or
  • Indulging in horseplay on the job.

Remember, because all accidents are caused by an unsafe condition or act, it is possible to prevent them. Do a thorough safety audit on your jobsite. Correct all unsafe conditions and report all unsafe acts.

If an accident does occur, do a safety investigation – not simply to find fault or place blame, but to find out what needs to be corrected so that future accidents can be prevented.

Most companies have safety rules to prevent unsafe acts. Practice them. Eventually, safety will become a habit – a habit that could save a life.

Download the recording form here

Why Seat Belts?

Originally published 10/17/2017

Do you drive a vehicle for your company, or operate a piece of heavy equipment on the construction site? If so, do you wear your seat belt?

  • People give all kinds of reasons for not wearing a seat belt.
  • “They’re uncomfortable.”
  • “I’m a good driver.”
  • “I don’t need to because my vehicle has air bags.”
  • “They wrinkle my clothes.”
  • “I’m afraid of getting stuck in the vehicle after a crash.”
  • And many more.

Seat belts promote safety by keeping you from hitting the windshield, being thrown from a vehicle, or banging around inside the vehicle and hitting the steering wheel or door if you’re in an accident.

In off-road equipment, your seat belt is foremost designed to keep you in your seat in case of a tip-over. Normal human behavior is to try to jump when a piece of equipment starts to tip. The problem is, you can’t get away from the machine fast enough and the machine will most likely end up crushing you at the head, neck, shoulders or chest. So in a tip-over, you want to wear your seat belt, keep your hands and feet in the cab, lean away from the point of impact and ride it out.

Before you get in your vehicle, know your surroundings. Are there steep slopes or unstable ground?

Inspect your seat belts. Look for broken, missing or frayed belts or damaged belt buckles, and report any problems to your supervisor. Do not use the equipment or drive the vehicle until the seat belts are operating properly.

When you put on your seat belt, be sure to wear it properly. Don’t put the strap under your arm or behind your back. Be sure to cinch the belt tight so that it surrounds your torso and fits snugly.

Be sure the equipment is completely turned off, the parking brake is engaged and the equipment is parked on a level, stable surface before you remove your seat belt.

If your company doesn’t have a seat belt policy, talk to a supervisor about setting one. If you make it a point to buckle up every time you get in a vehicle, eventually you won’t even have to think about it. It will be a habit – a habit that could help you avoid serious injury or even death. Remember, it’s up to you to make safe decisions.

Download the recording form here.

Cylinder Storage & Safety

Originally published 10/3/2017

Mishandled cylinders may rupture violently, release their hazardous contents or become dangerous projectiles. Special precautions are necessary when storing and handling compressed gas cylinders. Carelessness, abuse and complacency can result in a disaster.

Recommendations for cylinder storage:

  • Store cylinders in an upright position and secure them to a fixed location, such as a wall or work bench. Secure each cylinder at a point approximately 2/3 of its height.
  • Use appropriate material such as chains, plastic coated wire cable or commercially available cylinder straps to secure cylinders. Secure them individually, i.e., one restraint per cylinder.
  • Do not store gas cylinders in public hallways, beneath egress stairways or other unprotected areas.
  • Do not store cylinders near an actual or potential heat source, or where it will be exposed to weather extremes.
  • Segregate the cylinders in hazard classes for storage. At the minimum, oxidizers (such as oxygen) must be separated from flammable gases.
  • Isolate empty cylinders from filled cylinders. Do not discard them in the normal trash.
  • Do not store cylinders where heavy objects could fall on them.

To transport cylinders:

  • Be sure the valve protection cap is in place.
  • Do not use the protective valve cap for moving or lifting the cylinder.
  • Do not drag, slide or roll the cylinder. Use a cylinder cart or truck to move the cylinder(s).
  • Do not drop a cylinder, or permit cylinders to strike each other violently or be handled roughly.
  • Never transport a cylinder with the regulator in place.
  • Secure the cylinder to the cart or truck during transport.

Before and during use:

  • Use only the regulator designed for the material in use.
  • Do not grease or oil the regulator or cylinder valves.
  • Open the valve slowly and only with the proper regulator in place. Open it all the way.
  • Do not leave the valve open when the equipment is not in use – even if the cylinder is empty.
  • Keep the cylinder clear of all sparks, flames and electrical circuits.
  • Never rely on the color coding to identify the gas. Different manufacturers may use different coding systems.
  • Don’t use oxygen in place of compressed air.
  • Don’t use copper fittings or tubing on acetylene tanks as an explosion may result.
  • Wear appropriate PPE for the hazard potential of the material you are working with.

Most people think the cylinders on their worksite are safe. However, cylinders are safe only if treated properly. Make sure you know how to handle them.

 Download the recording form here.